can clip
Vident iAuto702 Pro is an upgraded powerful multi-application service tool which covers the majority of special functions available on all brands in the market. Combined with Vident's technical strength and popularity of iLink450 on market,covering ABS and SRS diagnosis, iAuto702Pro offers 39 special functions to help workshops.
VIDENT iAuto 702 Pro Multi-Applicaton Service Tool with 39 Special Functions 3 Years Free Update Online is a one of our can clip Tools, you can buy VIDENT iAuto 702 Pro Multi-Applicaton Service Tool with 39 Special Functions 3 Years Free Update Online from svcidiag.com.
Wholesale Top quality VAS6154, GM Tech2, VCM II For Ford, Handy Baby II Car Key Chip Copier, CDP DS150
images of VIDENT iAuto 702 Pro Multi-Applicaton Service Tool with 39 Special Functions 3 Years Free Update Online
VIDENT iAuto 702 Pro Multi-Applicaton Service Tool
VIDENT iAuto 702 Pro Highlights:
VIDENT iAuto 702Pro Product Function:
1. OBDII/EOBD+CAN Functions
Read codes
Clear codes
Vehicle information
Live data
View freeze frame data
I/M readiness
O2 monitor test
On-board monitor test
Component test
Modules present
2. ABS and SRS Diagnosis
Read codes
Clear codes
Vehicle information
Live data
View freeze frame data
Component test/active test
Adaptation
VIDENT iAuto 702Pro 39 Special Function:
iAuto702Pro has most of special functions of the mainstream tools on the market. Besides,support most of car brand in market for ABS and SRS system scan.
1. ABS, Antilock Brake Reset
The auto bleed procedure is used on BOSH 5.3 equipped vehicles. This procedure uses a scan tool to cycle the system solenoid valves and run the pump in order to purge the air from the secondary circuits.
2. SRS Airbag Crash Data Reset
Your airbag crash data module will be restored back to its factory condition after accidents
3. SAS Steering Angel Sensor Reset
helps clear the fault steering angle sensor memories and plays an important role in the steering angle sensor calibration.
4. EPB Electronic Park Brake Reset
If the brake pad wears the brake pad sense line, the brake pad sense line sends a signal sense line to the on-board computer to replace the brake pad. After replacing the brake pad, you must reset the brake pad. Otherwise, the car alarms.
Reset must be performed in the following cases:
●The brake pad and brake pad wear sensor are replaced.
●The brake pad indicator lamp is on.
●The brake pad sensor circuit is short, which is recovered.
●The servo motor is replaced. It is important in the maintenance of electronic braking systemrsquos safety and efficiency when replace brake pad or motor
5. DPF Diesel Particulate Filter Reset
specially works for Diesel Particulate Filter system with DPF regeneration, DPF component replacement teach-in and DPF teach-in after replacing the engine control unit.
6. Oil Service Light Reset
allows you to perform reset maintenance mileage and data intervals for a new calculation of Engine Oil Life system once changed the oil.
7. TPMS Tire Pressure Monitoring Sytem Reset
makes tpms senser in displaying sensor IDs from the vehiclersquos ECU, inputting TPMS sensor replacement IDs and activate tpms sensors.
8. TBA/TPS Throttle Body Alignment Reset
vehicle's throttle position system sensor connected to the butterfly spindle and is primarily used to monitor the throttle position within an inner combustion engine. Due to its location, the throttle position sensor is able to effectively observe where the throttle butterfly valve is positioned.
9. CVT Transmission fucntion
On these CVT transmissions, the timing of the release and application of elements (clutch packs and bands) is controlled by the transmission control module (a microprocessor)
10. BRT Battery Management Service
allows the scan tool to evaluate the battery charge state, monitor the close-circuit current, register the new battery replacement, and activate the rest state of the vehicle battery system
11. Injector Coding
diesel injector code need programming ID and parameters to the ECU for accurate communication and Injection control system
12. Camshaft Gear Learning
The scan tool monitors certain Camshaft position sensors signals to determine if all conditions are met to continue with the procedure for Engine running
13. Odometer Instrument Cluster Initialize
Instrument panel mileage calibration is used to copy, write, or rewrite mileages. That is, use the car diagnostic computer and data line to copy, write, or rewrite chip data on the instrument panel to make the instrument panel display actual mileages.
Usually, when the vehicle speed sensor is damaged or the mileage is incorrect due to instrument panel faults, you must perform mileage calibration after maintenance.
14. AFS (Adaptive Front Lighting System)
This function is used to initialize the adaptive headlight system. The adaptive headlight system determines whether to automatically turn on the headlight according to ambient light intensity, monitors driving speed and body posture, and adjusts the headlight lighting angle.
15. AF (Adjust Fuel)
16.TURBO
This routine is required if the secondary turbo charger is replaced. This will learn the offset values for the turbine shut-off valve.
17. Immobilizer
To prevent the car being used by unauthorized keys, the anti-theft key matching function must be performed so that the immobilizer control system on the car identifies and authorizes remote control keys to normally use the car.
When the ignition switch key, ignition switch, combined instrument panel, ECU, BCM, or remote control battery is replaced, anti-theft key matching must be performed.
18. Seat Match (adjust memory seat)
A memory seat is essentially an electrically-adjustable car seat which can be moved into pre-set positions at the push of a button. As a result of the removal of the DCC fuse, the "driving position memory" function of the driver and passenger side seat will be inoperative due to the loss of seat position memory stored in the seat ECU. The seat (position control) ECU may need to be initialized if the seat memory settings cannot be recorded.
19. Windows Door match
When replacing door glass and after battery replacement on certain year, make, model vehicles special steps need to be taken in order to properly replace and reprogram the vehicle so the electric windows work properly, the door window glass position can be learned by executing this routine, which enables pinch protection and one touch up function.
20. Language change
This routine is to change language displayed in the instrument.
21. Sunroof Initialization
This function is used to set sunroof lockup close, close on rainy days, slide/tilt sunroof memory function, outside temperature threshold, etc.
22. Gearbox match
This function is used to learn the gearbox to improve shift quality.
After the gearbox is dismounted or repaired (after battery powered off for some car series), shift delay or impact is caused. In this case, perform this function to make the gearbox compensate automatically according to driving conditions so as to reach more comfortable and ideal shift quality.
23. Clutch match (clutch pedal free-play)
Importance of clutch pedal free-play. Anything less than the correct amount of free play (or clearance) will result in clutch slip, because the pressure plate will be unable to exert its full pressure on the friction plate, clutch linkage adjustment to compensate for clutch wear.
24. Suspension Match
This function is used to adjust car body height.
When the car body height sensor and control module in the air suspension system are replaced or the car level is incorrect, perform this function to adjust the car body height sensor for horizontal calibration.
25. PFP (Prime Fuel Pump function)
The program can detect the Prime Fuel Pump function.
Air often gets into the fuel line when a diesel vehicle change fuel or assembly fuel system. This causes a vehicle to have problems starting, forcing you to "prime" the fuel system to remove the air.
26. AT Adaption
After each repair or transmission service, the transmission adaptation control will cause the Transmission Control Module (TCM) to relearn the change in transmission tolerances to improve the transmission quality, and to adjust the transition of the gear shift according to the driving style.\nThis procedure is used to clear the adaptive values in the transmission control unit. This may be required when changing the transmission, downloading software, or performing any other gearbox-related activity.\n\nThis command allows the adaptive shift points to be relearnt. CAUTION: Refer to workshop manual for correct procedure.
27.Change Tire Size
The vehicle's computer calculates your vehicle's speed based on the diameter of the stock tires. After changing the tire size, the vehicle's computer doesn't know how fast your vehicle is running, which will affect speedometer accuracy or transmission shift time. This routine is to recalibrate speedometer after changing the tire size..
28.EGR(Exhaust-gas recirculation) Adaption
This Function Is Used To Learn The EGR (Exhaust Gas Recirculation) Valve After It Is Cleaned Or Replaced..
29.Evaporative test
The EVAP system monitor checks for fuel vapor leaks by performing either a pressure or vacuum test on the fuel system. This routine is will create a positive pressure in the tank to determine if there are any leaks in the fuel system.
30.Transmission module Oil Life Reset
This program can be executed to Transmission control module oil counter reset
31.Replace Airbag ECU
32. ADblue-urea Reset
33. COOLANT-electronic Water Pump Start
34. Power Balance-Engine Power Balance
35. HVOLBAT-High-voltage Battery Health Detection
36. Moter Angle- motor Angle Calibration
37. NOx Reset-NOx Reset
38. Stopstart-start and Stop Settings
39. Transport-Remove Transport Mode
Notice: These special function NOT for all car models, if you are not sure, please contract us and send us your car make, type and year , we will check it for you.
VIDENT iAuto 702 Pro Highlights:
1. Covers Over 65 Car Makes to Latest 2020/2021.
2. Support ABS/SRS Full Scan. Support most of the car brands in the market for ABS and SRS system scan.read codes,clear codes,vehicle information,live data,view freeze frame data,component test/active test,adaptation.
3. Support 39 Special function like EPB/BRT/Oil light Reset/TPS/TPMS/IMMO/DPF/ODOMETER/Injector Coding/SAS/Gear Learning/ABS Bleed/Gearbox Matching/Suspension Matc/Sunroof Initialization/AFS/Adjust Fuel
Newly Add ADblue, COOLANT, Power Balance, HVOLBAT, Moter Angle, NOx Reset, Stopstart and Transport
4. Free Update Online for 3 Years, After 3 Years it will cost $60/year.
5. Support OBDII/EOBD+CAN Functions: Read codes,clear codes,vehicle information,live data ,view freeze frame data,I/M readiness,O2 monitor test,on-board monitor test,component test,modules present.
6. 4.3"LCD Color Display, clearly arranged keys, menu driven operation, and shortcuts together make this device extremely easy to use
7. Multi-Language: English, Spanish, German, French, Portuguese, Swedish, Italian, Russian, Japanese, Korean, Hungarian, Thai, Simplified Chinese and Traditional Chinese.
2. Support ABS/SRS Full Scan. Support most of the car brands in the market for ABS and SRS system scan.read codes,clear codes,vehicle information,live data,view freeze frame data,component test/active test,adaptation.
3. Support 39 Special function like EPB/BRT/Oil light Reset/TPS/TPMS/IMMO/DPF/ODOMETER/Injector Coding/SAS/Gear Learning/ABS Bleed/Gearbox Matching/Suspension Matc/Sunroof Initialization/AFS/Adjust Fuel
Newly Add ADblue, COOLANT, Power Balance, HVOLBAT, Moter Angle, NOx Reset, Stopstart and Transport
4. Free Update Online for 3 Years, After 3 Years it will cost $60/year.
5. Support OBDII/EOBD+CAN Functions: Read codes,clear codes,vehicle information,live data ,view freeze frame data,I/M readiness,O2 monitor test,on-board monitor test,component test,modules present.
6. 4.3"LCD Color Display, clearly arranged keys, menu driven operation, and shortcuts together make this device extremely easy to use
7. Multi-Language: English, Spanish, German, French, Portuguese, Swedish, Italian, Russian, Japanese, Korean, Hungarian, Thai, Simplified Chinese and Traditional Chinese.
VIDENT iAuto 702Pro Product Function:
1. OBDII/EOBD+CAN Functions
Read codes
Clear codes
Vehicle information
Live data
View freeze frame data
I/M readiness
O2 monitor test
On-board monitor test
Component test
Modules present
2. ABS and SRS Diagnosis
Read codes
Clear codes
Vehicle information
Live data
View freeze frame data
Component test/active test
Adaptation
VIDENT iAuto 702Pro 39 Special Function:
iAuto702Pro has most of special functions of the mainstream tools on the market. Besides,support most of car brand in market for ABS and SRS system scan.
1. ABS, Antilock Brake Reset
The auto bleed procedure is used on BOSH 5.3 equipped vehicles. This procedure uses a scan tool to cycle the system solenoid valves and run the pump in order to purge the air from the secondary circuits.
2. SRS Airbag Crash Data Reset
Your airbag crash data module will be restored back to its factory condition after accidents
3. SAS Steering Angel Sensor Reset
helps clear the fault steering angle sensor memories and plays an important role in the steering angle sensor calibration.
4. EPB Electronic Park Brake Reset
If the brake pad wears the brake pad sense line, the brake pad sense line sends a signal sense line to the on-board computer to replace the brake pad. After replacing the brake pad, you must reset the brake pad. Otherwise, the car alarms.
Reset must be performed in the following cases:
●The brake pad and brake pad wear sensor are replaced.
●The brake pad indicator lamp is on.
●The brake pad sensor circuit is short, which is recovered.
●The servo motor is replaced. It is important in the maintenance of electronic braking systemrsquos safety and efficiency when replace brake pad or motor
5. DPF Diesel Particulate Filter Reset
specially works for Diesel Particulate Filter system with DPF regeneration, DPF component replacement teach-in and DPF teach-in after replacing the engine control unit.
6. Oil Service Light Reset
allows you to perform reset maintenance mileage and data intervals for a new calculation of Engine Oil Life system once changed the oil.
7. TPMS Tire Pressure Monitoring Sytem Reset
makes tpms senser in displaying sensor IDs from the vehiclersquos ECU, inputting TPMS sensor replacement IDs and activate tpms sensors.
8. TBA/TPS Throttle Body Alignment Reset
vehicle's throttle position system sensor connected to the butterfly spindle and is primarily used to monitor the throttle position within an inner combustion engine. Due to its location, the throttle position sensor is able to effectively observe where the throttle butterfly valve is positioned.
9. CVT Transmission fucntion
On these CVT transmissions, the timing of the release and application of elements (clutch packs and bands) is controlled by the transmission control module (a microprocessor)
10. BRT Battery Management Service
allows the scan tool to evaluate the battery charge state, monitor the close-circuit current, register the new battery replacement, and activate the rest state of the vehicle battery system
11. Injector Coding
diesel injector code need programming ID and parameters to the ECU for accurate communication and Injection control system
12. Camshaft Gear Learning
The scan tool monitors certain Camshaft position sensors signals to determine if all conditions are met to continue with the procedure for Engine running
13. Odometer Instrument Cluster Initialize
Instrument panel mileage calibration is used to copy, write, or rewrite mileages. That is, use the car diagnostic computer and data line to copy, write, or rewrite chip data on the instrument panel to make the instrument panel display actual mileages.
Usually, when the vehicle speed sensor is damaged or the mileage is incorrect due to instrument panel faults, you must perform mileage calibration after maintenance.
14. AFS (Adaptive Front Lighting System)
This function is used to initialize the adaptive headlight system. The adaptive headlight system determines whether to automatically turn on the headlight according to ambient light intensity, monitors driving speed and body posture, and adjusts the headlight lighting angle.
15. AF (Adjust Fuel)
16.TURBO
This routine is required if the secondary turbo charger is replaced. This will learn the offset values for the turbine shut-off valve.
17. Immobilizer
To prevent the car being used by unauthorized keys, the anti-theft key matching function must be performed so that the immobilizer control system on the car identifies and authorizes remote control keys to normally use the car.
When the ignition switch key, ignition switch, combined instrument panel, ECU, BCM, or remote control battery is replaced, anti-theft key matching must be performed.
18. Seat Match (adjust memory seat)
A memory seat is essentially an electrically-adjustable car seat which can be moved into pre-set positions at the push of a button. As a result of the removal of the DCC fuse, the "driving position memory" function of the driver and passenger side seat will be inoperative due to the loss of seat position memory stored in the seat ECU. The seat (position control) ECU may need to be initialized if the seat memory settings cannot be recorded.
19. Windows Door match
When replacing door glass and after battery replacement on certain year, make, model vehicles special steps need to be taken in order to properly replace and reprogram the vehicle so the electric windows work properly, the door window glass position can be learned by executing this routine, which enables pinch protection and one touch up function.
20. Language change
This routine is to change language displayed in the instrument.
21. Sunroof Initialization
This function is used to set sunroof lockup close, close on rainy days, slide/tilt sunroof memory function, outside temperature threshold, etc.
22. Gearbox match
This function is used to learn the gearbox to improve shift quality.
After the gearbox is dismounted or repaired (after battery powered off for some car series), shift delay or impact is caused. In this case, perform this function to make the gearbox compensate automatically according to driving conditions so as to reach more comfortable and ideal shift quality.
23. Clutch match (clutch pedal free-play)
Importance of clutch pedal free-play. Anything less than the correct amount of free play (or clearance) will result in clutch slip, because the pressure plate will be unable to exert its full pressure on the friction plate, clutch linkage adjustment to compensate for clutch wear.
24. Suspension Match
This function is used to adjust car body height.
When the car body height sensor and control module in the air suspension system are replaced or the car level is incorrect, perform this function to adjust the car body height sensor for horizontal calibration.
25. PFP (Prime Fuel Pump function)
The program can detect the Prime Fuel Pump function.
Air often gets into the fuel line when a diesel vehicle change fuel or assembly fuel system. This causes a vehicle to have problems starting, forcing you to "prime" the fuel system to remove the air.
26. AT Adaption
After each repair or transmission service, the transmission adaptation control will cause the Transmission Control Module (TCM) to relearn the change in transmission tolerances to improve the transmission quality, and to adjust the transition of the gear shift according to the driving style.\nThis procedure is used to clear the adaptive values in the transmission control unit. This may be required when changing the transmission, downloading software, or performing any other gearbox-related activity.\n\nThis command allows the adaptive shift points to be relearnt. CAUTION: Refer to workshop manual for correct procedure.
27.Change Tire Size
The vehicle's computer calculates your vehicle's speed based on the diameter of the stock tires. After changing the tire size, the vehicle's computer doesn't know how fast your vehicle is running, which will affect speedometer accuracy or transmission shift time. This routine is to recalibrate speedometer after changing the tire size..
28.EGR(Exhaust-gas recirculation) Adaption
This Function Is Used To Learn The EGR (Exhaust Gas Recirculation) Valve After It Is Cleaned Or Replaced..
29.Evaporative test
The EVAP system monitor checks for fuel vapor leaks by performing either a pressure or vacuum test on the fuel system. This routine is will create a positive pressure in the tank to determine if there are any leaks in the fuel system.
30.Transmission module Oil Life Reset
This program can be executed to Transmission control module oil counter reset
31.Replace Airbag ECU
32. ADblue-urea Reset
33. COOLANT-electronic Water Pump Start
34. Power Balance-Engine Power Balance
35. HVOLBAT-High-voltage Battery Health Detection
36. Moter Angle- motor Angle Calibration
37. NOx Reset-NOx Reset
38. Stopstart-start and Stop Settings
39. Transport-Remove Transport Mode
Notice: These special function NOT for all car models, if you are not sure, please contract us and send us your car make, type and year , we will check it for you.
VIDENT iAuto 702Pro Specifications:
| Kit Includes | ||||||
| iAuto702Pro Multi-applicaton Service Tool | iAuto702Pro Scanner | |||||
| User Manual | ||||||
| Memory Card | ||||||
| Password Paper | ||||||
| Leather Carrying Pouch | ||||||
| Specification | Display: 4.3” Backlit, 480*272 TFT color screen | |||||
| Operating Temperature: 0 to 60°C (32 to 140°F) | ||||||
| Storage Temperature: -20 to 70°C (-4 to 158°F) | ||||||
| Power: 8 to 18 V provided via vehicle | ||||||
| Supported Protocols: ISO15765(CANBUS 11bit&29bit TP16, TP20, UDS, FIAT CAN, VOLVO CAN), ISO14230(KWP2000), ISO9141-2, J1850VPW, J1850PWM,KWP1281, KWP2089, KW81, KW82, ALDL, SCI, DSI, DSII, LUCAS, MELCO, BENIX, ISO7800, SIMENMS_ISO1, SIMENMS_ISO2, MIT MODE1, MIT MODE2, Mitsubishi Negative Logic protocol, Nissan-specific protocol. | ||||||
| Tool Dimensions: 212*117*47mm (L*W*H) | ||||||
VIDENT iAuto 702Pro Vehicle Coverage:
| ABS,SRS Diagnosis | Abarth, Acura, Alfa, AstonMartin, Audi, Bentley, BMW, Bugatti, Chrysler, Citroen, Dacia, Dawoo, Eu_Ford, Ferrari, Fiat, Ford, GM, Holden, Honda, Hyundai, Infiniti, Isuzu, Jaguar, KIA, Lamborghini, LANCIA, Landrover, Lexus, Maserati, Maybach, Mazda, Mercedes-Benz, Mini, Mitsubishi, Nissan, Opel, Perodua, Peugeot, Porsche, Proton, Renault, SAAB, Scion, Seat, Skoda, Smart, Sprinter, SsangYong, Subaru, Suzuki, Toyota,Vauxhall, Volvo, VW, VW_CV | |
| Common maintenance (special) functions: Oil Light Service/Reset | Abarth, Acura, Astonmartin, Audi,Baic, Bentley, BJXD, BMW, Bugatti, BYD, Chang An, Chery, Chrysler, Citroen, Dacia, Daewoo, DF Citroen, DF Peugeot, DF Honda, Faw Car, Ferrari, Fiat, Ford, GM, GQ Honda, GQ Toyota, Great Wall, HC BMW, Holden, Honda, Hyundai, Infiniti, Isuzu, JAC, Jaguar, Kia,Karry, Lamborghini, Lancia, Landrover, Lexus, Luxgen, Maserati, Maybach, Mazda, Mercedes-Benz, Mini, Mitsubishi, Nissan, Opel, Peugeot, Porsche, Proton, Rely, Renault, Riich, Rolls-Royce, Romeo, Rover, Saab, Scion, Seat, SHVW, Skoda, Smart, Sprinter, Subaru, Suzuki, Toyota, Vauxhall, Volvo, VW, Yema, YQ Mazda, YQ Toyota, YQ VW, Zotye | |
| Common maintenance (special) functions: EPB(Electronic Parking Brake) | Abarth, Acura, Alfa, Audi, Bentley, BJXD, BMW, Bugatti, BYD, Chery, Chrysler, Citroen, Daewoo, DF Citroen, DF Honda, DF Peugeot, Faw Besturn, Ferrari, Fiat, Ford, GM, GQ Honda, GQ Toyota, HC BMW, Honda, Hyundai, Jaguar, Kia, Lancia, Landrover, Lexus, Maserati, Maybach, Mazda, Mercedes-Benz, Mini, Opel, Peugeot, Porsche, Renault, Rolls-Roye, Romeo, Saab, Scion, Seat, SHVW, Skoda, Subaru, Toyota, Vauxhall, Volvo, VW, YQ Mazda, YQ Toyota, YQ VW, Zotye | |
| Common maintenance (special) functions: BRT(Battery Configuration) | Audi, Bentley, BMW, Bugatti, Chang An Ford, Chrysler, Citroen, DF Citroen, DF Nissan, DF Peugeot, Faw Car, Fiat, Ford, GQ Toyota, HC BMW,Hyundai,Infiniti,Jaguar, Kia, Lamborghini, Lancia, Landrover, Lexus, Mazda, Mini, Mitsubishi, Nissan, Opel, Peugeot, Porsche, Seat, SHVW, Skoda, Toyota, Volvo, VW, YQ Mazda, YQ Toyota, YQ VW | |
| Common maintenance (special) functions: DPF(Regeneration of Diesel Particulate Filter) | Acura, Audi, BMW, Chrysler, Citroen, Daewoo, DF Honda, Fiat, Ford, GM, GQ Honda, GQ Mazda, Honda, Hyundai, Infiniti, Jaguar, KIA, Lancia, Landrover, Lexus, Maserati, Mazda, Mercedes-Benz, Mini, Mitsubishi, Nissan, Opel, Peugeot, Porsche, Renault, Romeo, Scion, Seat, Skoda, Subaru, Suzuki, Toyota, Vauxhall, Volvo, VW | |
| Common maintenance (special) functions: TBA/TPS(Throttle Body Alignment) | Acura, Audi, BJXD, BMW, Brilliance, BYD, Chang An, Chang An Ford, Chery, Chrysler, Citroen, Dacia, Daewoo, Dfcitroen, DFFX, DF Honda, DF Nissan, DF Peugeot, DFPV, Faw Besturn, Faw Car, Faw Tianjin, Fiat, Ford, Geely, GM, GQ Honda, GQ Toyota, Great Wall, Haima, Haima Zhengzhou, HC, BMW, Honda, Huizhong, Hyundai, Infiniti, Jac, Jaguar, Kia, Lancia, Landrover, Lexus, Lifan, Maybach, Mazda, Mercedes-Benz, Mini, Mitsubishi, Nissan, Nissan Zhengzhou, Opel, Peugeot, Porsche, Proton, Rely, Renault, Riich, Romeo, Saab, Seat, SHVW, Skoda, Suzuki, Toyota, Vauxhall, Volvo, VW, Wuling, Young Lotus, YQ Toyota, YQ VW, Zhongxing | |
| Common maintenance (special) functions: Injector Coding | Acura, Audi, BMW, Chery, Chrysler, Citroen, Fiat, Ford, GM, DF Honda, Fiat, GQ Honda, Honda, Hyundai, Infiniti, Jaguar, Lancia, Landrover, Lexus, Mazda, Mercedes-Benz, Mini, Mitsubishi, Nissan, Peugeot, Porsche, Renault, Romeo, Smart, Seat, Skoda, Subaru, Suzuki, Toyota, Volvo, VW | |
| Common maintenance (special) functions: TPMS(Tire Pressure Measuring Sensor Reset) | Acura, Audi, BJXD, BMW, BYD, Chrysler, DF Honda, DF Nissan, Ferrari, Fiat, Ford, GQ Honda, GQ Toyota, Honda, Hyundai, Infiniti, Jaguar, KIA, Lancia, Landrover, Lexus, Maserati, Mazda, Mercedes-Benz, Mini, Mitsubishi, Nissan, Peugeot, Porsche, Renault, Scion, SHVW, Seat, Skoda, Smart, Subaru, Toyota, Volvo, VW, YQ Toyota, YQ VW | |
| Common maintenance (special) functions: SAS(Steering Angle Sensor Reset) | Acura, Audi, BJXD, BMW, BYD, ChanganFord, Chery, Chrysler, Citroen, Dacia, Daewoo, Daihatsu, DFCITROEN, DFFX, DF Honda, DF Nissan, DF Peugeot, DFPV, Faw Besturn, Faw Car, Ferrari, Fiat, Ford, Geely, GM, GQ Honda, GQ Toyota, Great wall, Haima, HC BMW, Honda, Hyundai, Infiniti, JAC,Jaguar, Karry, KIA, Lancia, Landrover, Lexus, Maserati, Maybach, Mazda, Mercedes-Benz, Mini, Mitsubishi, Nissan, Opel, Peugeot, Porsche, Proton, Renault, Romeo, Scion, Seat, SHVW, Skoda, Smart, Subaru, Suzuki, Toyota, Vauxhall, Volvo, VW, Yinxiang, YQ Mazda, YQ Toyota, YQ VW | |
| Common maintenance (special) functions: Immobilizer Programming | Acura, Audi, BAIC, Beijing Jeep, BJXD, BMW, Brilliance, BYD, Chang An, Chang An Ford, Chang He, Chery, Chrysler, Citroen, DF Citroen, DFFX, DF Honda, DF Nissan, DF Peugeot, DFPV, Dong Nan, Faw Car, Faw Tianjin, Fiat, Ford, Geely, GM, GQ Honda, GQ Toyota, Greatwall, Haima, Honda, Huizhong, Hyundai, Infiniti, JAC, Jaguar, Kia, Lancia, Landrover, Lexus, Mazda, Mercedes-Benz, Mitsubishi, Nissan, Nissan Zhengzhou, Peugeot, Renault, Romeo, Scion, Seat, SHVW, Skoda, Smart, Ssangyong, Suzuki, Toyota, VW, Wuling, Yongyuan, Young Lotus, YQ Mazda, YQ Toyota, YQ VW, Zhonghua | |
| Common maintenance (special) functions: Gear Learning | Chang An, Chery, DFFX, Geely, JAC, Nissan ZhengZhou, Great Wall | |
| Common maintenance (special) functions: ABS Bleed | Acura, BJXD, BMW, BYD, Chang An, Chang He, Chery, Chrysler, Citroen, Daewoo, Daihatsu, DFFX, DF Honda, FawBesturn, Ferrari, Fiat, Ford, Geely, GQ Honda, GQ Toyota, Greatwall, Haima, HC BMW, Honda, Hyundai, JAC, Jaguar, Jiachuang, Karry, Kia,Lancia, Landrover, Lexus, Liebao, Maserati, Mazda, Mercedes-Benz, Mini, Mitsubishi, MYHR, NJYWK, Opel, Peugeot, Proton, Rely, Renault, RIICH, Romeo, Saab, Scion, Smart, Ssangyong, Toyato, Vauxhall, Yema, Yinxiang, YQ Mazda, YQ Toyota, Zhongshun | |
| Common maintenance (special) functions: Gearbox Match | Ford | |
| Common maintenance (special) functions: Suspension Match | Jaguar, Landrover, Mercendes-Benz | |
| Common maintenance (special) functions: Sunroof Initialization | BMW | |
| Common maintenance (special) functions: AFS (Adaptive Front Lighting System) | Audi, Baic, Bentley, BYD, Chang An, Chery, Great Wall, Haima, Jaguar, Landrover, Roewe, Seat, Skoda, VW, Zotye | |
| Common maintenance (special) functions: Adjuste Fuel | Fiat, Ford, GM, VW | |
| Common maintenance (special) functions: Odometer Calibration | GM, Infiniti, Nissan, Opel, Roewe, Vauxhall | |
How to update VIDENT iAuto 702 Pro?
Step1: Please register users name&password on official website:www.videnttech.com
Step 2:Download and install upgrade tool, then enter user name&password to log in.
Step 3: Pull out the TF card of the device and plug into computer to upgrade,finally plug TF card back device.
VIDENT iAuto 702 Pro Product Display:
VIDENT iAuto 702 Pro Package includes:
1pc x VIDENT iAuto 702Pro
1pc x User's Guide
1pc x Memory Card
1pc x Leather Carrying Pouch
1pc x Password Envelope